History: Greenhouse Project

Source of version: 29

!溫室之心 The Mind Of A GreenHouse, Nangqen {img type="fileId" fileId="14" thumb="box" max="240"} from airport to our site. [https://www.youtube.com/watch?v=UsBOWeiHKEI|video] !!Project Introduction This is an on going research project in Tibet, I joined this charity project voluntarily since August 2018 with Wiriar Rattanansuwan, a climate engineer from Thailand. The project goal is to build a solar greenhouse in Nangqen which can resist -20Cº to -30Cº during November to February in Nangqen. The altitude of the site is ~3,700 meters; the main task is to provide vegetable year-round for for the orphan children sheltered by the school. Another main task of this project is to research a common ground for both charity project and art, science project. The reason of it is to de-alienated artist or scientist from other capital systems, to innovate a transdiciplinary production system, social design. Also I believe the innovative project collaborating with the local community will bring more attentions to the situation of these developing areas. !!Design In the first phase of the design, we tried to employ many solutions and assemble them into one design. Solutions including earth battery, pit-house, earth-sheltered design to make a passive solar house. The design of this first prototype was 4*6*2 meters in size, 2 meters deep in depth. *Pit-house: The [https://www.wikiwand.com/en/Pit-house|history of pit-house] can be found here. We decided to make our one two meters deep due to the extreme weather in Nangqen. It was made of white iron frame and transparent Polycarbonate, PC boards with multilayers, sealed with silicon. We use bricks to build the walls underground to maintain the basement shape. We didn't put the bricks as floors, so the plants grow on the floor. Inside the house is proximately 4 to 6 degrees warmer than the outdoor temperature. *Earth Battery: For the earth battery part, we connected an underground PC pipe to the house, in order to drain the cold air out and circulate it back to the house after heat it underground through a 11 meters long tube. *IoT Weather sensor: Unfortunately we only finished the 80% construction before my flight, I tried to install one RPI board with v2 camera module with it as weather sensor. It took me 3 or 4 days to find a local internet cafe to install Raspian. They were quit paranoid to see I was working with wires and codes in their cafe, so I quickly got kicked out. Eventually I made it done and has successfully get the sensor datas, camera vision via ssh. Unfortunately I didn’t have time to install it properly inside the house before my flight to Taipei. weather data station by Raspberry Pi (library: https://github.com/nickoala/sensor) *Roof: We thought about to make the roof with glass windows but luckly and eventually I choose transparent PC with multiple layers. I am very glad I made the choice due to it's low weight and cheap price, and it was so much easier to install compare to the glass windows. However I only sliced the whole roof into 9 pieces in my design which cause a big problem for the installing, 12 to 20 slices would made the job much easier. Roof angle and house orientation: by the coordinates longitude: 32.8250 latitude: 97.1250, we got the sun azimuth angle around 79º, and our roof slope should be 23º. The greenhouse is facing to south with 11º degrees counterclockwise turned in order to get the maximum sunlight. {img type="fileId" fileId="5, 7, 9, 10, 11" thumb="box" widths="200"} Earth battery, earth sheltered greenhouse, were the two major prototype of our first design. There wasn’t enough time to accomplish the earth battery part when I was there since this is our first attempt because I didn’t find good pipes there for the air circulating. The earth sheltered design worked well, according to the feedbacks from the local community after I got back to Taiwan, they say they sweat and they see water dripping inside which proved the indoor temperature is above zero in the winter time. They also tell that they feel dizzy want to puke after long staying in it, I guess that is because we only have installed one fan for the air circulating and that causes short of oxygen and too much CO2 inside. OPV test for NTSU, 成功大學 OPV provided by professor Meng Hsin Fei from NTSU, These OPV has relatively very low watts, it is used to power one small fan I found from local electronics shop for cold/warm air circulation. I didn’t find a good fan with proper size. , although the fan was quite small but still able to make strong wind. Those OPV was placed inside the greenhouse, unfortunately it was not able to get the battery full charged and the OPV all didn’t survive from the weather. I think it might be the cracks on the OPV caused the oxidation inside the protection glass. Construction progress photos. The weather station Latest result: DIY raised beds and the vagetables growing conditions. The vagetables in pictures are taken around Janurary 20th, it was plant in Novemeber 5th, the growing is very slow due to the coldness. It is averagely -20 degrees from Novermber to December, however inside the greenhouse can be up above 0 degree so the water are still in liquid form inside. The problem now is the soil and we didn’t chose plants has higher resistance to cold to grow, we will select plants grow in cold weather in phase 2 of the project, which will take place in April 2019. !!2018 project developers: [https://www.facebook.com/wiriyar.Rattanasuwan|Wiriya Rattanansuwan], Shih Wei Chieh principal of Tashi Gatsen Charity School: Tsansar Kunga land owner: Tsngsar Metokk local coordinators: Tsangsar Tsueji, Tsansar Mohji

History

Enable pagination rows per page

HTML diff Side-by-side diff Side-by-side diff by characters Inline diff Inline diff by characters Full side-by-side diff Full side-by-side diff by characters Full inline diff Full inline diff by characters Unified diff Side-by-side view HTML diff Side-by-side diff Advanced

Information	Version
2023-11-21 11:06 admin	148
2023-11-21 11:00 admin	147
2023-11-21 10:59 admin	146
2023-11-21 10:57 admin img Plugin modified by editor.	145
2023-11-21 10:57 admin img Plugin modified by editor.	144
2023-11-21 10:57 admin img Plugin modified by editor.	143
2023-11-21 10:57 admin img Plugin modified by editor.	142
2023-11-21 10:56 admin img Plugin modified by editor.	141
2023-11-21 10:56 admin img Plugin modified by editor.	140
2023-11-21 10:56 admin img Plugin modified by editor.	139
2023-11-21 10:55 admin img Plugin modified by editor.	138
2023-11-21 10:55 admin img Plugin modified by editor.	137
2023-11-21 10:54 admin img Plugin modified by editor.	136
2023-11-21 10:54 admin img Plugin modified by editor.	135
2023-11-21 10:54 admin img Plugin modified by editor.	134
2023-11-21 10:54 admin img Plugin modified by editor.	133
2023-11-21 10:54 admin img Plugin modified by editor.	132
2023-11-21 10:53 admin img Plugin modified by editor.	131
2023-11-21 10:53 admin img Plugin modified by editor.	130
2023-11-21 10:53 admin img Plugin modified by editor.	129
2023-11-21 10:53 admin img Plugin modified by editor.	128
2023-11-21 10:53 admin img Plugin modified by editor.	127
2023-11-21 10:52 admin img Plugin modified by editor.	126
2023-11-21 10:52 admin img Plugin modified by editor.	125
2023-11-21 10:46 admin img Plugin modified by editor.	124

Select action to perform with checked... Remove OK

• «
• 1 (current)
• 2
• 3
• 4
• 5
• 6
• »